Syllable Forum Index Syllable
Syllable Forums
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

radeon driver puts monitor frequency out of range
Goto page 1, 2  Next
 
Post new topic   Reply to topic    Syllable Forum Index -> Bugs
View previous topic :: View next topic  
Author Message
adamk



Joined: 15 Dec 2007
Posts: 54

PostPosted: Fri Mar 20, 2009 4:04 pm    Post subject: radeon driver puts monitor frequency out of range Reply with quote

The video card is an x850. I installed via qemu, but tried to boot natively. Unfortunately, when the appserver kicks in, both monitors turn off (the LCD turns off immediately, the CRT displays the out-of-range message and turns off after a few seconds). Here's the serial debug:

[code:1]
0 : CPU: Intel(R) Xeon(TM) CPU 3.20GHz (family 0xf model 0x6)
0 : Multiboot memory map:
0 : 0000000000000000 - 000000000009ec00 (usable)
0 : 00000000000f0000 - 0000000000100000 (reserved)
0 : 0000000000100000 - 000000007fe0ac00 (usable)
0 : 000000007fe0ac00 - 000000007fe0cc00 (ACPI NVS)
0 : 000000007fe5cc00 - 000000007fe5ec00 (ACPI data)
0 : 000000007fe0ec00 - 0000000080000000 (reserved)
0 : 00000000e0000000 - 00000000f0000000 (reserved)
0 : 00000000fe000000 - 00000000fec00000 (reserved)
0 : 00000000fed00000 - 00000000fed00400 (reserved)
0 : 00000000fec90000 - 00000000fee00000 (reserved)
0 : 00000000fef00000 - 00000000ff000000 (reserved)
0 : 00000000fec00000 - 00000000fec90000 (reserved)
0 : 00000000fee00000 - 00000000fef00000 (reserved)
0 : 00000000ffb00000 - 0000000100000000 (reserved)
0 : Scan memory for ACPI SMP config tables...
0 : Scan memory for MPC SMP config tables...
0 : Intel SMP v1.4
0 : Virtual Wire compatibility mode.
0 : OEM ID: DELL Product ID: WS 490
0 : Processor #0 Unknown CPU [15:6] APIC version 20
0 : Floating point unit present.
0 : Machine Exception supported.
0 : 64 bit compare & exchange supported.
0 : Internal APIC present.
0 : Bootup CPU
0 : Processor #2 Unknown CPU [15:6] APIC version 20
0 : Floating point unit present.
0 : Machine Exception supported.
0 : 64 bit compare & exchange supported.
0 : Internal APIC present.
0 : Bus 0 is PCI
0 : Bus 1 is PCI
0 : Bus 2 is PCI
0 : Bus 3 is PCI
0 : Bus 4 is PCI
0 : Bus 5 is PCI
0 : Bus 6 is PCI
0 : Bus 7 is PCI
0 : Bus 8 is PCI
0 : Bus 9 is PCI
0 : Bus 10 is PCI
0 : Bus 11 is PCI
0 : Bus 12 is PCI
0 : Bus 13 is ISA
0 : I/O APIC 8 Version 32 at 0xFEC00000.
0 : I/O APIC 9 Version 32 at 0xFEC80000.
0 : 2 processors found.
0 : Boot from CPU #0.
0 : Calibrating delay loop for CPU 0
0 : CPU 0 - 4243.45 BogoMIPS (lpj=2121728)
0 : CPU 0 runs at 3191.6943 MHz
0 : CPU 0 bus runs at 265.9966 MHz
0 : Start init thread
0:init::init(-1) : Booting processor #2
2 : Calibrating delay loop for CPU 2
2 : CPU 2 - 4243.45 BogoMIPS (lpj=2121728)
2 : CPU 2 runs at 3191.8149 MHz
2 : CPU 2 bus runs at 266.0050 MHz
2 : MTRR descriptors written
0:init::init(-1) : Total of 2 processors activated (8486.91 BogoMIPS).
0:init::init(-1) : Enable interrupts
0:init::init(-1) : TIME : 20-03-2009 17:57:11
0:init::init(-1) : Kernel configuration: /boot/system/config/kernel.cfg
0:init::init(-1) : IRQ 4 enabled
0:init::init(-1) : Init virtual file system
dbg>0:init::init(-1) : Volume 1 (0x001649a0) added
0:init::init(-1) : Root file system mounted 0x001649a0
0:init::init(-1) : Volume 3 (0x00164bc0) added
0:init::init(-1) : Init boot modules:
0:init::init(-1) : Init boot module '/boot/system/drivers/dev/bus/acpi'
0:init::init(-1) : Init boot module '/boot/system/drivers/dev/bus/pci'
0:init::init(-1) : Init boot module '/boot/system/drivers/dev/bus/ata'
0:init::init(-1) : Init boot module '/boot/system/drivers/dev/hcd/ata_pci'
0:init::init(-1) : Init boot module '/boot/system/drivers/fs/afs'
0:init::init(-1) : Reenabling device /boot/system/drivers/dev/acpi_cpu
0:init::init(-1) : Reenabling device /boot/system/drivers/dev/battery
0:init::init(-1) : ACPI: RSDP 000FEBF0, 0024 (r2 DELL )
0:init::init(-1) : ACPI: XSDT 000FCE54, 006C (r1 DELL B8K D ASL 61)
0:init::init(-1) : ACPI: FACP 000FCF7C, 00F4 (r3 DELL B8K D ASL 61)
0:init::init(-1) : ACPI: DSDT FFF5E688, 3BCC (r1 DELL dt_ex 1000 INTL 20050624)
0:init::init(-1) : ACPI: FACS 7FE0AC00, 0040
0:init::init(-1) : ACPI: SSDT FFF62254, 0099 (r1 DELL st_ex 1000 INTL 20050624)
0:init::init(-1) : ACPI: APIC 000FD070, 009E (r1 DELL B8K D ASL 61)
0:init::init(-1) : ACPI: BOOT 000FD10E, 0028 (r1 DELL B8K D ASL 61)
0:init::init(-1) : ACPI: ASF! 000FD136, 0067 (r16 DELL B8K D ASL 61)
0:init::init(-1) : ACPI: MCFG 000FD19D, 003E (r1 DELL B8K D ASL 61)
0:init::init(-1) : ACPI: HPET 000FD1DB, 0038 (r1 DELL B8K D ASL 61)
0:init::init(-1) : ACPI: TCPA 000FD437, 0032 (r1 DELL B8K D ASL 61)
0:init::init(-1) : ACPI: SLIC 000FD213, 0176 (r1 DELL B8K D ASL 61)
0:init::init(-1) : IRQ 9 enabled
0:init::init(-1) : ACPI: Using PIC for interrupt routing
0:init::init(-1) : ACPI: Found System \ [0xffffffff] ACPI ACPI_SYS
0:init::init(-1) : ACPI: Found Power Button PWRB [0x00000000] PWRF ACPI_FPB
0:init::init(-1) : ACPI: Found Processor \_PR_.CPU0 [0x00e44d38] CPU0 ACPI_CPU
0:init::init(-1) : ACPI: Found Processor \_PR_.CPU1 [0x00e44d58] CPU1 ACPI_CPU
0:init::init(-1) : ACPI: Found Processor \_PR_.CPU2 [0x00e44d78] CPU2 ACPI_CPU
0:init::init(-1) : ACPI: Found Processor \_PR_.CPU3 [0x00e44d98] CPU3 ACPI_CPU
0:init::init(-1) : ACPI: Found Processor \_PR_.CPU4 [0x00e44db8] CPU4 ACPI_CPU
0:init::init(-1) : ACPI: Found Processor \_PR_.CPU5 [0x00e44dd8] CPU5 ACPI_CPU
0:init::init(-1) : ACPI: Found Processor \_PR_.CPU6 [0x00e44df8] CPU6 ACPI_CPU
0:init::init(-1) : ACPI: Found Processor \_PR_.CPU7 [0x00e44e18] CPU7 ACPI_CPU
0:init::init(-1) : ACPI: Found Device \_SB_ [0x00e44478] _SB
0:init::init(-1) : ACPI: Found Device \_SB_.VBTN [0x00e445b8] VBTN PNP0C0C
0:init::init(-1) : ACPI: Found Device \_SB_.PCI0 [0x00e44f38] PCI0 PNP0A03
0:init::init(-1) : ACPI: Found Device \_SB_.PCI0.PCI2 [0x00f84078] PCI2
0:init::init(-1) : ACPI: Found Device \_SB_.PCI0.PCI2.PCI3 [0x00f84258] PCI3
0:init::init(-1) : ACPI: Found Device \_SB_.PCI0.PCI2.PCI3.PCIF [0x00f84438] PCIF
0:init::init(-1) : ACPI: Found Device \_SB_.PCI0.PCI2.PCI5 [0x00f84618] PCI5
0:init::init(-1) : ACPI: Found Device \_SB_.PCI0.PCI6 [0x00f847f8] PCI6
0:init::init(-1) : ACPI: Found Device \_SB_.PCI0.PCI7 [0x00f84a18] PCI7
0:init::init(-1) : ACPI: Found Device \_SB_.PCI0.PCIA [0x00f84c38] PCIA
0:init::init(-1) : ACPI: Found Device \_SB_.PCI0.PCIB [0x00f84d18] PCIB
0:init::init(-1) : ACPI: Found Device \_SB_.PCI0.PCIC [0x00f84df8] PCIC
0:init::init(-1) : ACPI: Found Device \_SB_.PCI0.PCI8 [0x00f84ed8] PCI8
0:init::init(-1) : ACPI: Found Device \_SB_.PCI0.PCI9 [0x00f86058] PCI9
0:init::init(-1) : ACPI: Found Device \_SB_.PCI0.ISA_ [0x00f86278] ISA
0:init::init(-1) : ACPI: Found Device \_SB_.PCI0.ISA_.MBIO [0x00f86318] MBIO PNP0C01
0:init::init(-1) : ACPI: Found Device \_SB_.PCI0.ISA_.DMA_ [0x00f86918] DMA PNP0200
0:init::init(-1) : ACPI: Found Device \_SB_.PCI0.ISA_.FPU_ [0x00f86978] FPU PNP0C04
0:init::init(-1) : ACPI: Found Device \_SB_.PCI0.ISA_.PIC_ [0x00f869d8] PIC PNP0000
0:init::init(-1) : ACPI: Found Device \_SB_.PCI0.ISA_.SPK_ [0x00f86a38] SPK PNP0800
0:init::init(-1) : ACPI: Found Device \_SB_.PCI0.ISA_.RTC_ [0x00f86a98] RTC PNP0B00
0:init::init(-1) : ACPI: Found Device \_SB_.PCI0.ISA_.TMR_ [0x00f86af8] TMR PNP0100
0:init::init(-1) : ACPI: Found Device \_SB_.PCI0.ISA_.KBD_ [0x00f88af8] KBD PNP0303
0:init::init(-1) : ACPI: Found Device \_SB_.PCI0.ISA_.MOU_ [0x00f88b78] MOU PNP0F13
0:init::init(-1) : ACPI: Found Device \_SB_.PCI0.ISA_.COMA [0x00f88cd8] COMA PNP0501
0:init::init(-1) : ACPI: Found Device \_SB_.PCI0.USB0 [0x00f86398] USB0
0:init::init(-1) : ACPI: Found Device \_SB_.PCI0.USB1 [0x00f864d8] USB1
0:init::init(-1) : ACPI: Found Device \_SB_.PCI0.USB2 [0x00f86618] USB2
0:init::init(-1) : ACPI: Found Device \_SB_.PCI0.USB3 [0x00f86758] USB3
0:init::init(-1) : ACPI: Found Device \_SB_.LNKA [0x00f86c58] LNKA PNP0C0F
0:init::init(-1) : ACPI: Found Device \_SB_.LNKB [0x00f86d58] LNKB PNP0C0F
0:init::init(-1) : ACPI: Found Device \_SB_.LNKC [0x00f86e58] LNKC PNP0C0F
0:init::init(-1) : ACPI: Found Device \_SB_.LNKD [0x00f86f58] LNKD PNP0C0F
0:init::init(-1) : ACPI: Found Device \_SB_.LNKE [0x00f88078] LNKE PNP0C0F
0:init::init(-1) : ACPI: Found Device \_SB_.LNKF [0x00f88178] LNKF PNP0C0F
0:init::init(-1) : ACPI: Found Device \_SB_.LNKG [0x00f88278] LNKG PNP0C0F
0:init::init(-1) : ACPI: Found Device \_SB_.LNKH [0x00f88378] LNKH PNP0C0F
0:init::init(-1) : ACPI: Found Device \_SB_.HPET [0x00f88478] HPET PNP0103
0:init::init(-1) : ACPI: Found Thermal Zone \_TZ_ [0x00e444b8] _TZ ACPI_THM
0:init::init(-1) : ACPI: S0 S1 S3 S4 S5 supported
0:init::init(-1) : ACPI: Register driver ACPI Thermal Zone Driver
0:init::init(-1) : ACPI: Register driver ACPI Fan Driver
0:init::init(-1) : ACPI: Register driver ACPI Power Resource Driver
0:init::init(-1) : ACPI: Register driver ACPI Embedded Controller Driver
0:init::init(-1) : ACPI: Register driver ACPI Button Driver
0:init::init(-1) : ACPI: Power Button (FF) [PWRF]
0:init::init(-1) : ACPI: Wakeup devices VBTN PCI0 PCI2 PCI3 PCIF PCI5 PCI6 PCI7 PCI8 PCI9 KBD USB0 USB1 USB2 USB3
0:init::init(-1) : ACPI: Busmanager initialized
0:init::init(-1) : PCI: PCIBIOS Version 2.16 detected
0:init::init(-1) : PCI: Access method 1 supported, access method 2 not supported
0:init::init(-1) : PCI: Using access method 1
0:init::init(-1) : PCI: Scanning Bus 0
0:init::init(-1) : PCI: Device 0 VendorID: 8086 DeviceID: 25c0 at 0:0:0
0:init::init(-1) : PCI: Device 1 VendorID: 8086 DeviceID: 25e2 at 0:2:0
0:init::init(-1) : PCI: Scanning Bus 1
0:init::init(-1) : PCI: Device 2 VendorID: 8086 DeviceID: 3500 at 1:0:0
0:init::init(-1) : PCI: Scanning Bus 2
0:init::init(-1) : PCI: Device 3 VendorID: 8086 DeviceID: 3510 at 2:0:0
0:init::init(-1) : PCI: Scanning Bus 3
0:init::init(-1) : PCI: Scan of bus finished
0:init::init(-1) : PCI: Device 4 VendorID: 8086 DeviceID: 3514 at 2:1:0
0:init::init(-1) : PCI: Scanning Bus 4
0:init::init(-1) : PCI: Scan of bus finished
0:init::init(-1) : PCI: Scan of bus finished
0:init::init(-1) : PCI: Device 5 VendorID: 8086 DeviceID: 350c at 1:0:3
0:init::init(-1) : PCI: Scanning Bus 5
0:init::init(-1) : PCI: Scan of bus finished
0:init::init(-1) : PCI: Scan of bus finished
0:init::init(-1) : PCI: Device 6 VendorID: 8086 DeviceID: 25e3 at 0:3:0
0:init::init(-1) : PCI: Scanning Bus 6
0:init::init(-1) : PCI: Scan of bus finished
0:init::init(-1) : PCI: Device 7 VendorID: 8086 DeviceID: 25fa at 0:4:0
0:init::init(-1) : PCI: Scanning Bus 7
0:init::init(-1) : PCI: Device 8 VendorID: 1002 DeviceID: 5d4d at 7:0:0
0:init::init(-1) : PCI: Device 9 VendorID: 1002 DeviceID: 5d6d at 7:0:1
0:init::init(-1) : PCI: Scan of bus finished
0:init::init(-1) : PCI: Device 10 VendorID: 8086 DeviceID: 25e5 at 0:5:0
0:init::init(-1) : PCI: Scanning Bus 8
0:init::init(-1) : PCI: Scan of bus finished
0:init::init(-1) : PCI: Device 11 VendorID: 8086 DeviceID: 25e6 at 0:6:0
0:init::init(-1) : PCI: Scanning Bus 9
0:init::init(-1) : PCI: Scan of bus finished
0:init::init(-1) : PCI: Device 12 VendorID: 8086 DeviceID: 25e7 at 0:7:0
0:init::init(-1) : PCI: Scanning Bus 10
0:init::init(-1) : PCI: Scan of bus finished
0:init::init(-1) : PCI: Device 13 VendorID: 8086 DeviceID: 25f0 at 0:16:0
0:init::init(-1) : PCI: Device 14 VendorID: 8086 DeviceID: 25f0 at 0:16:1
0:init::init(-1) : PCI: Device 15 VendorID: 8086 DeviceID: 25f0 at 0:16:2
0:init::init(-1) : PCI: Device 16 VendorID: 8086 DeviceID: 25f1 at 0:17:0
0:init::init(-1) : PCI: Device 17 VendorID: 8086 DeviceID: 25f3 at 0:19:0
0:init::init(-1) : PCI: Device 18 VendorID: 8086 DeviceID: 25f5 at 0:21:0
0:init::init(-1) : PCI: Device 19 VendorID: 8086 DeviceID: 25f6 at 0:22:0
0:init::init(-1) : PCI: Device 20 VendorID: 8086 DeviceID: 269a at 0:27:0
0:init::init(-1) : PCI: Device 21 VendorID: 8086 DeviceID: 2690 at 0:28:0
0:init::init(-1) : PCI: Scanning Bus 11
0:init::init(-1) : PCI: Device 22 VendorID: 14e4 DeviceID: 1600 at 11:0:0
0:init::init(-1) : PCI: Scan of bus finished
0:init::init(-1) : PCI: Device 23 VendorID: 8086 DeviceID: 2688 at 0:29:0
0:init::init(-1) : PCI: Device 24 VendorID: 8086 DeviceID: 2689 at 0:29:1
0:init::init(-1) : PCI: Device 25 VendorID: 8086 DeviceID: 268a at 0:29:2
0:init::init(-1) : PCI: Device 26 VendorID: 8086 DeviceID: 268b at 0:29:3
0:init::init(-1) : PCI: Device 27 VendorID: 8086 DeviceID: 268c at 0:29:7
0:init::init(-1) : PCI: Device 28 VendorID: 8086 DeviceID: 244e at 0:30:0
0:init::init(-1) : PCI: Scanning Bus 12
0:init::init(-1) : PCI: Device 29 VendorID: 1102 DeviceID: 0002 at 12:2:0
0:init::init(-1) : PCI: Device 30 VendorID: 1102 DeviceID: 7002 at 12:2:1
0:init::init(-1) : PCI: Scan of bus finished
0:init::init(-1) : PCI: Device 31 VendorID: 8086 DeviceID: 2670 at 0:31:0
0:init::init(-1) : PCI: Device 32 VendorID: 8086 DeviceID: 269e at 0:31:1
0:init::init(-1) : PCI: Device 33 VendorID: 8086 DeviceID: 2681 at 0:31:2
0:init::init(-1) : PCI: Device 34 VendorID: 8086 DeviceID: 269b at 0:31:3
0:init::init(-1) : PCI: Scan of bus finished
0:init::init(-1) : PCI: 35 devices detected
0:init::init(-1) : ACPI: Register driver ACPI PCI Interrupt Link Driver
0:init::init(-1) : PCI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 15)
0:init::init(-1) : PCI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 9 10 11 12 15)
0:init::init(-1) : PCI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 9 10 11 12 15)
0:init::init(-1) : PCI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled.
0:init::init(-1) : PCI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 *9 10 11 12 15)
0:init::init(-1) : PCI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 *10 11 12 15)
0:init::init(-1) : PCI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 *9 10 11 12 15)
0:init::init(-1) : PCI: PCI Interrupt Link [LNKH] (IRQs *3 4 5 6 7 9 10 11 12 15)
0:init::init(-1) : ACPI: Register driver ACPI PCI Root Bridge Driver
0:init::init(-1) : PCI: [PCI0] (00:00)
0:init::init(-1) : PCI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
0:init::init(-1) : PCI: Routing Table Entry 0:0 Pin 0
0:init::init(-1) : Connected to link: \_SB_.LNKA:0
0:init::init(-1) : PCI: Routing Table Entry 0:0 Pin 1
0:init::init(-1) : Connected to link: \_SB_.LNKB:0
0:init::init(-1) : PCI: Routing Table Entry 0:0 Pin 2
0:init::init(-1) : Connected to link: \_SB_.LNKC:0
0:init::init(-1) : PCI: Routing Table Entry 0:0 Pin 3
0:init::init(-1) : Connected to link: \_SB_.LNKD:0
0:init::init(-1) : PCI: Routing Table Entry 0:2 Pin 0
0:init::init(-1) : Connected to link: \_SB_.LNKA:0
0:init::init(-1) : PCI: Routing Table Entry 0:2 Pin 1
0:init::init(-1) : Connected to link: \_SB_.LNKB:0
0:init::init(-1) : PCI: Routing Table Entry 0:2 Pin 2
0:init::init(-1) : Connected to link: \_SB_.LNKC:0
0:init::init(-1) : PCI: Routing Table Entry 0:2 Pin 3
0:init::init(-1) : Connected to link: \_SB_.LNKD:0
0:init::init(-1) : PCI: Routing Table Entry 0:3 Pin 0
0:init::init(-1) : Connected to link: \_SB_.LNKA:0
0:init::init(-1) : PCI: Routing Table Entry 0:3 Pin 1
0:init::init(-1) : Connected to link: \_SB_.LNKB:0
0:init::init(-1) : PCI: Routing Table Entry 0:3 Pin 2
0:init::init(-1) : Connected to link: \_SB_.LNKC:0
0:init::init(-1) : PCI: Routing Table Entry 0:3 Pin 3
0:init::init(-1) : Connected to link: \_SB_.LNKD:0
0:init::init(-1) : PCI: Routing Table Entry 0:4 Pin 0
0:init::init(-1) : Connected to link: \_SB_.LNKA:0
0:init::init(-1) : PCI: Routing Table Entry 0:4 Pin 1
0:init::init(-1) : Connected to link: \_SB_.LNKB:0
0:init::init(-1) : PCI: Routing Table Entry 0:4 Pin 2
0:init::init(-1) : Connected to link: \_SB_.LNKC:0
0:init::init(-1) : PCI: Routing Table Entry 0:4 Pin 3
0:init::init(-1) : Connected to link: \_SB_.LNKD:0
0:init::init(-1) : PCI: Routing Table Entry 0:5 Pin 0
0:init::init(-1) : Connected to link: \_SB_.LNKA:0
0:init::init(-1) : PCI: Routing Table Entry 0:5 Pin 1
0:init::init(-1) : Connected to link: \_SB_.LNKB:0
0:init::init(-1) : PCI: Routing Table Entry 0:5 Pin 2
0:init::init(-1) : Connected to link: \_SB_.LNKC:0
0:init::init(-1) : PCI: Routing Table Entry 0:5 Pin 3
0:init::init(-1) : Connected to link: \_SB_.LNKD:0
0:init::init(-1) : PCI: Routing Table Entry 0:6 Pin 0
0:init::init(-1) : Connected to link: \_SB_.LNKA:0
0:init::init(-1) : PCI: Routing Table Entry 0:6 Pin 1
0:init::init(-1) : Connected to link: \_SB_.LNKB:0
0:init::init(-1) : PCI: Routing Table Entry 0:6 Pin 2
0:init::init(-1) : Connected to link: \_SB_.LNKC:0
0:init::init(-1) : PCI: Routing Table Entry 0:6 Pin 3
0:init::init(-1) : Connected to link: \_SB_.LNKD:0
0:init::init(-1) : PCI: Routing Table Entry 0:7 Pin 0
0:init::init(-1) : Connected to link: \_SB_.LNKA:0
0:init::init(-1) : PCI: Routing Table Entry 0:7 Pin 1
0:init::init(-1) : Connected to link: \_SB_.LNKB:0
0:init::init(-1) : PCI: Routing Table Entry 0:7 Pin 2
0:init::init(-1) : Connected to link: \_SB_.LNKC:0
0:init::init(-1) : PCI: Routing Table Entry 0:7 Pin 3
0:init::init(-1) : Connected to link: \_SB_.LNKD:0
0:init::init(-1) : PCI: Routing Table Entry 0:27 Pin 0
0:init::init(-1) : Connected to link: \_SB_.LNKA:0
0:init::init(-1) : PCI: Routing Table Entry 0:28 Pin 0
0:init::init(-1) : Connected to link: \_SB_.LNKA:0
0:init::init(-1) : PCI: Routing Table Entry 0:28 Pin 1
0:init::init(-1) : Connected to link: \_SB_.LNKB:0
0:init::init(-1) : PCI: Routing Table Entry 0:28 Pin 2
0:init::init(-1) : Connected to link: \_SB_.LNKC:0
0:init::init(-1) : PCI: Routing Table Entry 0:28 Pin 3
0:init::init(-1) : Connected to link: \_SB_.LNKD:0
0:init::init(-1) : PCI: Routing Table Entry 0:29 Pin 0
0:init::init(-1) : Connected to link: \_SB_.LNKF:0
0:init::init(-1) : PCI: Routing Table Entry 0:29 Pin 1
0:init::init(-1) : Connected to link: \_SB_.LNKG:0
0:init::init(-1) : PCI: Routing Table Entry 0:29 Pin 2
0:init::init(-1) : Connected to link: \_SB_.LNKC:0
0:init::init(-1) : PCI: Routing Table Entry 0:29 Pin 3
0:init::init(-1) : Connected to link: \_SB_.LNKH:0
0:init::init(-1) : PCI: Routing Table Entry 0:30 Pin 0
0:init::init(-1) : Connected to link: \_SB_.LNKH:0
0:init::init(-1) : PCI: Routing Table Entry 0:30 Pin 1
0:init::init(-1) : Connected to link: \_SB_.LNKB:0
0:init::init(-1) : PCI: Routing Table Entry 0:31 Pin 0
0:init::init(-1) : Connected to link: \_SB_.LNKA:0
0:init::init(-1) : PCI: Routing Table Entry 0:31 Pin 1
0:init::init(-1) : Connected to link: \_SB_.LNKB:0
0:init::init(-1) : PCI: Routing Table Entry 0:31 Pin 2
0:init::init(-1) : Connected to link: \_SB_.LNKE:0
0:init::init(-1) : PCI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI2._PRT]
0:init::init(-1) : PCI: Routing Table Entry 1:0 Pin 0
0:init::init(-1) : Connected to link: \_SB_.LNKA:0
0:init::init(-1) : PCI: Routing Table Entry 1:0 Pin 1
0:init::init(-1) : Connected to link: \_SB_.LNKB:0
0:init::init(-1) : PCI: Routing Table Entry 1:0 Pin 2
0:init::init(-1) : Connected to link: \_SB_.LNKC:0
0:init::init(-1) : PCI: Routing Table Entry 1:0 Pin 3
0:init::init(-1) : Connected to link: \_SB_.LNKD:0
0:init::init(-1) : PCI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI2.PCI3._PRT]
0:init::init(-1) : PCI: Routing Table Entry 2:0 Pin 0
0:init::init(-1) : Connected to link: \_SB_.LNKA:0
0:init::init(-1) : PCI: Routing Table Entry 2:0 Pin 1
0:init::init(-1) : Connected to link: \_SB_.LNKB:0
0:init::init(-1) : PCI: Routing Table Entry 2:0 Pin 2
0:init::init(-1) : Connected to link: \_SB_.LNKC:0
0:init::init(-1) : PCI: Routing Table Entry 2:0 Pin 3
0:init::init(-1) : Connected to link: \_SB_.LNKD:0
0:init::init(-1) : PCI: Routing Table Entry 2:1 Pin 0
0:init::init(-1) : Connected to link: \_SB_.LNKA:0
0:init::init(-1) : PCI: Routing Table Entry 2:1 Pin 1
0:init::init(-1) : Connected to link: \_SB_.LNKB:0
0:init::init(-1) : PCI: Routing Table Entry 2:1 Pin 2
0:init::init(-1) : Connected to link: \_SB_.LNKC:0
0:init::init(-1) : PCI: Routing Table Entry 2:1 Pin 3
0:init::init(-1) : Connected to link: \_SB_.LNKD:0
0:init::init(-1) : PCI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI2.PCI3.PCIF._PRT]
0:init::init(-1) : PCI: Routing Table Entry 3:0 Pin 0
0:init::init(-1) : Connected to link: \_SB_.LNKA:0
0:init::init(-1) : PCI: Routing Table Entry 3:0 Pin 1
0:init::init(-1) : Connected to link: \_SB_.LNKB:0
0:init::init(-1) : PCI: Routing Table Entry 3:0 Pin 2
0:init::init(-1) : Connected to link: \_SB_.LNKC:0
0:init::init(-1) : PCI: Routing Table Entry 3:0 Pin 3
0:init::init(-1) : Connected to link: \_SB_.LNKD:0
0:init::init(-1) : PCI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI2.PCI5._PRT]
0:init::init(-1) : PCI: Routing Table Entry 5:11 Pin 0
0:init::init(-1) : Connected to link: \_SB_.LNKA:0
0:init::init(-1) : PCI: Routing Table Entry 5:11 Pin 1
0:init::init(-1) : Connected to link: \_SB_.LNKB:0
0:init::init(-1) : PCI: Routing Table Entry 5:5 Pin 0
0:init::init(-1) : Connected to link: \_SB_.LNKC:0
0:init::init(-1) : PCI: Routing Table Entry 5:5 Pin 1
0:init::init(-1) : Connected to link: \_SB_.LNKD:0
0:init::init(-1) : PCI: Routing Table Entry 5:5 Pin 2
0:init::init(-1) : Connected to link: \_SB_.LNKA:0
0:init::init(-1) : PCI: Routing Table Entry 5:5 Pin 3
0:init::init(-1) : Connected to link: \_SB_.LNKB:0
0:init::init(-1) : PCI: Routing Table Entry 5:6 Pin 0
0:init::init(-1) : Connected to link: \_SB_.LNKC:0
0:init::init(-1) : PCI: Routing Table Entry 5:6 Pin 1
0:init::init(-1) : Connected to link: \_SB_.LNKD:0
0:init::init(-1) : PCI: Routing Table Entry 5:6 Pin 2
0:init::init(-1) : Connected to link: \_SB_.LNKA:0
0:init::init(-1) : PCI: Routing Table Entry 5:6 Pin 3
0:init::init(-1) : Connected to link: \_SB_.LNKB:0
0:init::init(-1) : PCI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI6._PRT]
0:init::init(-1) : PCI: Routing Table Entry 6:0 Pin 0
0:init::init(-1) : Connected to link: \_SB_.LNKA:0
0:init::init(-1) : PCI: Routing Table Entry 6:0 Pin 1
0:init::init(-1) : Connected to link: \_SB_.LNKB:0
0:init::init(-1) : PCI: Routing Table Entry 6:0 Pin 2
0:init::init(-1) : Connected to link: \_SB_.LNKC:0
0:init::init(-1) : PCI: Routing Table Entry 6:0 Pin 3
0:init::init(-1) : Connected to link: \_SB_.LNKD:0
0:init::init(-1) : PCI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI7._PRT]
0:init::init(-1) : PCI: Routing Table Entry 7:0 Pin 0
0:init::init(-1) : Connected to link: \_SB_.LNKA:0
0:init::init(-1) : PCI: Routing Table Entry 7:0 Pin 1
0:init::init(-1) : Connected to link: \_SB_.LNKB:0
0:init::init(-1) : PCI: Routing Table Entry 7:0 Pin 2
0:init::init(-1) : Connected to link: \_SB_.LNKC:0
0:init::init(-1) : PCI: Routing Table Entry 7:0 Pin 3
0:init::init(-1) : Connected to link: \_SB_.LNKD:0
0:init::init(-1) : PCI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI8._PRT]
0:init::init(-1) : PCI: Routing Table Entry 11:0 Pin 0
0:init::init(-1) : Connected to link: \_SB_.LNKA:0
0:init::init(-1) : PCI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI9._PRT]
0:init::init(-1) : PCI: Routing Table Entry 12:10 Pin 0
0:init::init(-1) : Connected to link: \_SB_.LNKC:0
0:init::init(-1) : PCI: Routing Table Entry 12:2 Pin 0
0:init::init(-1) : Connected to link: \_SB_.LNKC:0
0:init::init(-1) : PCI: Routing Table Entry 12:2 Pin 1
0:init::init(-1) : Connected to link: \_SB_.LNKD:0
0:init::init(-1) : PCI: Routing Table Entry 12:2 Pin 2
0:init::init(-1) : Connected to link: \_SB_.LNKA:0
0:init::init(-1) : PCI: Routing Table Entry 12:2 Pin 3
0:init::init(-1) : Connected to link: \_SB_.LNKB:0
0:init::init(-1) : PCI: PCI Interrupt Link [LNKA] enabled at IRQ 11
0:init::init(-1) : PCI: Device 0x8086:0x25c0 IRQ transform 0 -> 11
0:init::init(-1) : PCI: Device 0x8086:0x25e2 IRQ transform 0 -> 11
0:init::init(-1) : PCI: Device 0x8086:0x3500 IRQ transform 11 -> 11
0:init::init(-1) : PCI: Device 0x8086:0x3510 IRQ transform 11 -> 11
0:init::init(-1) : PCI: Device 0x8086:0x3514 IRQ transform 3 -> 11
0:init::init(-1) : PCI: Device 0x8086:0x350c has no interrupt pin
0:init::init(-1) : PCI: Device 0x8086:0x25e3 IRQ transform 0 -> 11
0:init::init(-1) : PCI: Device 0x8086:0x25fa IRQ transform 0 -> 11
0:init::init(-1) : PCI: Device 0x1002:0x5d4d IRQ transform 11 -> 11
0:init::init(-1) : PCI: Device 0x1002:0x5d6d has no interrupt pin
0:init::init(-1) : PCI: Device 0x8086:0x25e5 IRQ transform 0 -> 11
0:init::init(-1) : PCI: Device 0x8086:0x25e6 IRQ transform 0 -> 11
0:init::init(-1) : PCI: Device 0x8086:0x25e7 IRQ transform 0 -> 11
0:init::init(-1) : PCI: Device 0x8086:0x25f0 has no interrupt pin
0:init::init(-1) : PCI: Device 0x8086:0x25f0 has no interrupt pin
0:init::init(-1) : PCI: Device 0x8086:0x25f0 has no interrupt pin
0:init::init(-1) : PCI: Device 0x8086:0x25f1 has no interrupt pin
0:init::init(-1) : PCI: Device 0x8086:0x25f3 has no interrupt pin
0:init::init(-1) : PCI: Device 0x8086:0x25f5 has no interrupt pin
0:init::init(-1) : PCI: Device 0x8086:0x25f6 has no interrupt pin
0:init::init(-1) : PCI: Device 0x8086:0x269a IRQ transform 11 -> 11
0:init::init(-1) : PCI: Device 0x8086:0x2690 IRQ transform 11 -> 11
0:init::init(-1) : PCI: Device 0x14e4:0x1600 IRQ transform 11 -> 11
0:init::init(-1) : PCI: PCI Interrupt Link [LNKF] enabled at IRQ 10
0:init::init(-1) : PCI: Device 0x8086:0x2688 IRQ transform 10 -> 10
0:init::init(-1) : PCI: PCI Interrupt Link [LNKG] enabled at IRQ 9
0:init::init(-1) : PCI: Device 0x8086:0x2689 IRQ transform 9 -> 9
0:init::init(-1) : PCI: PCI Interrupt Link [LNKC] enabled at IRQ 5
0:init::init(-1) : PCI: Device 0x8086:0x268a IRQ transform 5 -> 5
0:init::init(-1) : PCI: PCI Interrupt Link [LNKH] enabled at IRQ 3
0:init::init(-1) : PCI: Device 0x8086:0x268b IRQ transform 3 -> 3
0:init::init(-1) : PCI: Device 0x8086:0x268c IRQ transform 10 -> 10
0:init::init(-1) : PCI: Device 0x8086:0x244e has no interrupt pin
0:init::init(-1) : PCI: Device 0x1102:0x2 IRQ transform 5 -> 5
0:init::init(-1) : PCI: Device 0x1102:0x7002 has no interrupt pin
0:init::init(-1) : PCI: Device 0x8086:0x2670 has no interrupt pin
0:init::init(-1) : PCI: Device 0x8086:0x269e IRQ transform 11 -> 11
0:init::init(-1) : PCI: PCI Interrupt Link [LNKE] enabled at IRQ 9
0:init::init(-1) : PCI: Device 0x8086:0x2681 IRQ transform 9 -> 9
0:init::init(-1) : PCI: PCI Interrupt Link [LNKB] enabled at IRQ 5
0:init::init(-1) : PCI: Device 0x8086:0x269b IRQ transform 5 -> 5
0:init::init(-1) : ATA busmanager initialized
0:init::init(-1) : ATA PCI controller detected on 0:31:1
0:init::init(-1) : Controller in legacy mode
0:init::init(-1) : Channel 0: PIO Cmd @ 1f0 Ctrl @ 3f6 DMA @ ffa0 IRQ @ 14
0:init::init(-1) : Channel 1: PIO Cmd @ 170 Ctrl @ 376 DMA @ ffa8 IRQ @ 15
0:init::init(-1) : IRQ 14 enabled
0:init::init(-1) : IRQ 15 enabled
0:init::init(-1) : Intel ESB2 controller detected
0:init::init(-1) : Detected 1 ATA PCI controllers
0:init::init(-1) : ATA device connected on 80pin cable
0:init::init(-1) : Name: Maxtor 6Y080P0 (hda)
0:init::init(-1) : Modes: PIO ( 3 4 ) MWDMA ( 0 1 2 ) UDMA ( 0 1 2 3 4 5 6 )
0:init::init(-1) : Capacity: 81964 Mb
0:init::init(-1) : ATAPI device connected on 80pin cable
0:init::init(-1) : ATAPI CD-ROM/DVD-ROM connected on 80pin cable
0:init::init(-1) : Name: TSSTcorp CD-ROM TS-H192C (cdb)
0:init::init(-1) : Modes: PIO ( 3 4 ) MWDMA ( 0 1 2 ) UDMA ( 0 1 2 )
0:init::init(-1) : No device connected on port 1:0 (not present)
0:init::init(-1) : No device connected on port 1:1 (not present)
0:init::init(-1) : Maxtor 6Y080P0: Using Ultra DMA mode 5
0:init::init(-1) : TSSTcorp CD-ROM TS-H192C: Using Ultra DMA mode 2
0:init::init(-1) : Decode partition table for hda
2:init::init(-1) : Partition 0 : 32256 -> 2048385023 06 (2048352768)
2:init::init(-1) : Partition 1 : 2048385024 -> 9574225919 2a (7525840896)
2:init::init(-1) : Partition 2 : 9574225920 -> 45765457919 83 (36191232000)
2:init::init(-1) : Partition 3 : 45765457920 -> 81956689919 eb (36191232000)
2:init::init(-1) : Mount boot FS: /dev/disk/ata/hda/1 afs
2:init::init(-1) : initialize_fs called in afs
2:init::init(-1) : Mount afs on '/dev/disk/ata/hda/1' flags 00000000
2:init::init(-1) : Load super block
0:init::init(-1) : Validate super block
0:init::init(-1) : Log start: 938 BitmapStart : 34
0:init::init(-1) : afs_mount() : filesystem has 7075082 free blocks (of 7349454)
2:init::init(-1) : AFS filesystem successfully mounted
2:init::init(-1) : ACPI: Register driver ACPI Processor Driver
2:init::init(-1) : Error: Could not find physical processor id
2:init::init(-1) : ACPI Exception (evxface-0544): AE_NOT_EXIST, Removing notify handler [20080321]
2:init::init(-1) : Error: Could not find physical processor id
2:init::init(-1) : ACPI Exception (evxface-0544): AE_NOT_EXIST, Removing notify handler [20080321]
2:init::init(-1) : Error: Could not find physical processor id
2:init::init(-1) : ACPI Exception (evxface-0544): AE_NOT_EXIST, Removing notify handler [20080321]
2:init::init(-1) : Error: Could not find physical processor id
2:init::init(-1) : ACPI Exception (evxface-0544): AE_NOT_EXIST, Removing notify handler [20080321]
2:init::init(-1) : Error: Could not find physical processor id
2:init::init(-1) : ACPI Exception (evxface-0544): AE_NOT_EXIST, Removing notify handler [20080321]
2:init::init(-1) : Error: Could not find physical processor id
2:init::init(-1) : ACPI Exception (evxface-0544): AE_NOT_EXIST, Removing notify handler [20080321]
2:init::init(-1) : Error: Could not find physical processor id
2:init::init(-1) : ACPI Exception (evxface-0544): AE_NOT_EXIST, Removing notify handler [20080321]
2:init::init(-1) : Error: Could not find physical processor id
2:init::init(-1) : ACPI Exception (evxface-0544): AE_NOT_EXIST, Removing notify handler [20080321]
2:init::init(-1) : Disabling device /boot/system/drivers/dev/acpi_cpu on bus acpi
2:init::init(-1) : Error: device /boot/system/drivers/dev/acpi_cpu failed to initialize itself
2:init::init(-1) : ACPI: Register driver ACPI Battery Driver
2:init::init(-1) : Disabling device /boot/system/drivers/dev/battery on bus acpi
2:init::init(-1) : Error: device /boot/system/drivers/dev/battery failed to initialize itself
2:init::init(-1) : PS2 keyboard and mouse driver
2:init::init(-1) : PS2 or AT Keyboard detected
0:init::init(-1) : PS2 AUX port detected
0:init::init(-1) : AGP: Busmanager initialized
2:init::init(-1) : SCSI: Busmanager initialized
2:init::init(-1) : USB: Busmanager initialized
2:init::init(-1) : USB: USB HUB driver registered
0:init::init(-1) : IRQ 10 enabled
0:init::init(-1) : USB: Bus 0 registered
0:init::init(-1) : USB EHCI at I/O 0xff980800, IRQ 10
0:init::init(-1) : EHCI: USB 2.0 enabled, EHCI 1.00, driver 0.1
0:init::init(-1) : USB: New device strings: Mfr=3, Product=2, SerialNumber=1
0:init::init(-1) : Manufacturer: Syllable 0.6 EHCI
0:init::init(-1) : Product: USB EHCI Root Hub
0:init::init(-1) : SerialNumber: 0
0:init::init(-1) : 8 ports detected
0:init::init(-1) : USB: Device claimed by USB HUB driver
0:init::init(-1) : Device /boot/system/drivers/dev/hcd/usb_ohci on bus pci is disabled
0:init::init(-1) : USB UHCI at I/O 0xff80, IRQ 10
0:init::init(-1) : USB: Bus 1 registered
0:init::init(-1) : USB: New device strings: Mfr=0, Product=2, SerialNumber=1
0:init::init(-1) : Product: USB UHCI Root Hub
0:init::init(-1) : SerialNumber: ff80
0:init::init(-1) : 2 ports detected
0:init::init(-1) : USB: Device claimed by USB HUB driver
0:init::init(-1) : USB UHCI at I/O 0xff60, IRQ 9
0:init::init(-1) : USB: Bus 2 registered
0:init::init(-1) : USB: New device strings: Mfr=0, Product=2, SerialNumber=1
0:init::init(-1) : Product: USB UHCI Root Hub
0:init::init(-1) : SerialNumber: ff60
0:init::init(-1) : 2 ports detected
0:init::init(-1) : USB: Device claimed by USB HUB driver
0:init::init(-1) : USB UHCI at I/O 0xff40, IRQ 5
0:init::init(-1) : USB: Bus 3 registered
0:init::init(-1) : IRQ 5 enabled
0:init::init(-1) : USB: New device strings: Mfr=0, Product=2, SerialNumber=1
0:init::init(-1) : Product: USB UHCI Root Hub
0:init::init(-1) : SerialNumber: ff40
0:init::init(-1) : 2 ports detected
0:init::init(-1) : USB: Device claimed by USB HUB driver
0:init::init(-1) : USB UHCI at I/O 0xff20, IRQ 3
0:init::init(-1) : USB: Bus 4 registered
0:init::init(-1) : IRQ 3 enabled
0:init::init(-1) : USB: New device strings: Mfr=0, Product=2, SerialNumber=1
0:init::init(-1) : Product: USB UHCI Root Hub
0:init::init(-1) : SerialNumber: ff20
0:init::init(-1) : 2 ports detected
0:init::init(-1) : USB: Device claimed by USB HUB driver
0:init::init(-1) : Volume 5 (0x00164ec0) added
2:init::init(-1) : 3c509.c:0.51 October 9, 2000
2:init::init(-1) : ***NO 3c509 CARD FOUND***
2:init::init(-1) : Error: device /boot/system/drivers/dev/net/eth/3c509 failed to initialize itself
0:init::init(-1) : Error: device /boot/system/drivers/dev/net/eth/3c59x failed to initialize itself
0:init::init(-1) : Error: device /boot/system/drivers/dev/net/eth/8390 failed to initialize itself
0:init::init(-1) : Device /boot/system/drivers/dev/net/eth/dl2k on bus pci is disabled
0:init::init(-1) : Device /boot/system/drivers/dev/net/eth/dp83815 on bus pci is disabled
0:init::init(-1) : Device /boot/system/drivers/dev/net/eth/eepro100 on bus pci is disabled
0:init::init(-1) : Device /boot/system/drivers/dev/net/eth/forcedeth on bus pci is disabled
0:init::init(-1) : Device /boot/system/drivers/dev/net/eth/pcnet32 on bus pci is disabled
0:init::init(-1) : Device /boot/system/drivers/dev/net/eth/r8169 on bus pci is disabled
0:init::init(-1) : Device /boot/system/drivers/dev/net/eth/rtl8139 on bus pci is disabled
0:init::init(-1) : Device /boot/system/drivers/dev/net/eth/sis900 on bus pci is disabled
0:init::init(-1) : Device /boot/system/drivers/dev/net/eth/skge on bus pci is disabled
0:init::init(-1) : tg3: Tigon3 [partno(BCM5752KFBG) rev 6002 PHY(5752)] (PCI Express) 10/100/1000BaseT Ethernet
0:init::init(-1) : tg3: MAC: 00:18:8b:0a:6b:6f
0:init::init(-1) : tg3: RXcsums[0] LinkChgREG[1] MIirq[1] ASF[0] Split[0] WireSpeed[1] TSOcap[0]
0:init::init(-1) : tg3: dma_rwctrl[76180000]
0:init::init(-1) : Device /boot/system/drivers/dev/net/eth/tulip on bus pci is disabled
0:init::init(-1) : Device /boot/system/drivers/dev/net/eth/via on bus pci is disabled
0:init::init(-1) : pci_enable_msi not implemented!
0:init::init(-1) : IRQ 11 enabled
0:init::init(-1) : Start init host
0:boot-shell::boot-shell(-1) : Starting init...
0:sh::sh : Device /boot/system/drivers/dev/acpi_cpu on bus acpi is disabled
0:sh::sh : Device /boot/system/drivers/dev/battery on bus acpi is disabled
2:appserver::appserver : Appserver Alive 16
0:kernel::idle_00 : tg3: Link is up at 100 Mbps, full duplex.
0:kernel::idle_00 : tg3: Flow control is on for TX and on for RX.
2:appserver::appserver : Directory '/system/fonts/' scanned 92 fonts found
2:appserver::appserver : Load configuration
2:appserver::appserver : Start keyboard thread
2:appserver::appserver : Load default fonts
2:appserver::appserver : Initialise graphics driver...
2:appserver::appserver : Device /boot/system/drivers/dev/acpi_cpu on bus acpi is disabled
2:appserver::appserver : Device /boot/system/drivers/dev/battery on bus acpi is disabled
0:appserver::appserver : Device /boot/system/drivers/dev/graphics/geforcefx on bus pci is disabled
0:appserver::appserver : Device /boot/system/drivers/dev/graphics/i855 on bus pci is disabled
0:appserver::appserver : Device /boot/system/drivers/dev/graphics/mach64 on bus pci is disabled
0:appserver::appserver : Device /boot/system/drivers/dev/graphics/mga on bus pci is disabled
0:appserver::appserver : ATi Radeon X850 XT PE (R480) found
0:appserver::appserver : Device /boot/system/drivers/dev/graphics/riva on bus pci is disabled
0:appserver::appserver : Device /boot/system/drivers/dev/graphics/s3_chrome on bus pci is disabled
0:appserver::appserver : Device /boot/system/drivers/dev/graphics/s3_virge on bus pci is disabled
0:appserver::appserver : Device /boot/system/drivers/dev/graphics/savage on bus pci is disabled
0:appserver::appserver : Device /boot/system/drivers/dev/graphics/sis3xx on bus pci is disabled
0:appserver::appserver : Device /boot/system/drivers/dev/graphics/tdfx on bus pci is disabled
0:appserver::appserver : Error: device /boot/system/drivers/dev/graphics/trident failed to initialize itself
0:appserver::appserver : Device /boot/system/drivers/dev/graphics/vmware on bus pci is disabled
0:appserver::appserver : ATi Radeon X850 XT PE (R480) opened
0:appserver::appserver : Using AppServer driver radeon
2:appserver::appserver : Radeon :: ATi Radeon ]M detected.
0:appserver::appserver : Radeon :: Configuration file /system/config/drivers/appserver/video/radeon.cfg found, reading...
2:appserver::appserver : Radeon :: 9500 and higher support: enabled
2:appserver::appserver : Radeon :: Mobility/IGP support: enabled
2:appserver::appserver : Radeon :: Notebook CRT mirroring support: enabled
2:appserver::appserver : Radeon :: Debugging output: enabled
2:appserver::appserver : Radeon :: Card BIOS usage (disabling dangerous): enabled
0:appserver::appserver : Radeon :: Using MMIO at fcde0000
0:appserver::appserver : Radeon :: probed SDR SGRAM 262144k videoram
0:appserver::appserver : MTRR descriptors written
2:kernel::idle_02 : MTRR descriptors written
0:appserver::appserver : Radeon :: Using framebuffer at d0000000
0:appserver::appserver : Radeon :: ROM base address c0000
0:appserver::appserver : Radeon :: ROM size 20000
0:appserver::appserver : Radeon :: Found Intel x86 BIOS ROM Image
0:appserver::appserver : Radeon :: ATOM BIOS detected
0:appserver::appserver : Radeon :: Retrieved PLL infos from ATOM BIOS
0:appserver::appserver : Radeon :: Reference=27.00 MHz (RefDiv=2) Memory=590.00 Mhz, System=540.00 MHz
0:appserver::appserver : radeonfb: PLL min 20000 max 50000
0:appserver::appserver : Radeon :: Starting monitor auto detection...
0:appserver::appserver : Radeon :: Monitor 1 type CRT found
0:appserver::appserver : Radeon :: Monitor 2 type no found
0:appserver::appserver : Radeon :: Video mode 640x480 registered
0:appserver::appserver : Radeon :: Video mode 800x600 registered
0:appserver::appserver : Radeon :: Video mode 1024x768 registered
0:appserver::appserver : Radeon :: Video mode 1152x864 registered
0:appserver::appserver : Radeon :: Video mode 1280x1024 registered
0:appserver::appserver : Radeon :: Video mode 1400x1050 registered
0:appserver::appserver : Radeon :: Video mode 1600x1200 registered
0:appserver::appserver : Using graphics driver radeon
0:appserver::appserver : Radeon :: Error: Idle Timeout !
0:appserver::appserver : hStart = 656, hEnd = 752, hTotal = 800
0:appserver::appserver : vStart = 490, vEnd = 492, vTotal = 525
0:appserver::appserver : h_total_disp = 0x4f0063 hsync_strt_wid = 0x8c0291
0:appserver::appserver : v_total_disp = 0x1df020c vsync_strt_wid = 0x8201e9
0:appserver::appserver : pixclock = 39722
0:appserver::appserver : freq = 2517
0:appserver::appserver : ref_div = 2, ref_clk = 2700, output_freq = 20136
0:appserver::appserver : post div = 0x3
0:appserver::appserver : fb_div = 0xf
0:appserver::appserver : ppll_div_3 = 0x3000f
0:appserver::appserver : Warning: DisplayDriver::MouseOn() called while mouse visible
0:appserver::appserver : Probe input node keyboard
0:appserver::appserver : ps2_open()
0:appserver::appserver : IRQ 1 enabled
2:appserver::appserver : Probe input node ps2mouse
0:appserver::appserver : Device /boot/system/drivers/dev/acpi_cpu on bus acpi is disabled
0:appserver::appserver : Device /boot/system/drivers/dev/battery on bus acpi is disabled
0:appserver::appserver : Serial device: device_init() called
0:appserver::appserver : Serial device failed to install IRQ handler
0:appserver::appserver : Error: device /boot/system/drivers/dev/misc/serial failed to initialize itself
2:appserver::appserver : w8378x>init_driver()
2:appserver::appserver : w8378x>init_driver(): could not find hardware
2:appserver::appserver : Error: device /boot/system/drivers/dev/misc/w8378x failed to initialize itself
2:appserver::appserver : ps2_open()
2:appserver::appserver : IRQ 12 enabled
0:appserver::appserver : IMPS2 mouse detected.
2:appserver::appserver : Probe input node sermouse
0:appserver::appserver : Device /boot/system/drivers/dev/acpi_cpu on bus acpi is disabled
0:appserver::appserver : Device /boot/system/drivers/dev/battery on bus acpi is disabled
0:appserver::appserver : Serial device: device_init() called
0:appserver::appserver : Serial device failed to install IRQ handler
0:appserver::appserver : Error: device /boot/system/drivers/dev/misc/serial failed to initialize itself
0:appserver::appserver : w8378x>init_driver()
0:appserver::appserver : w8378x>init_driver(): could not find hardware
0:appserver::appserver : Error: device /boot/system/drivers/dev/misc/w8378x failed to initialize itself
0:appserver::appserver : Error: serial mode driver failed to open serial device: No such file or directory
0:appserver::appserver : Input node sermouse failed to initialize
2:appserver::appserver : Probe input node usbkeyboard
2:appserver::appserver : Device /boot/system/drivers/dev/acpi_cpu on bus acpi is disabled
2:appserver::appserver : Device /boot/system/drivers/dev/battery on bus acpi is disabled
2:appserver::appserver : USB: USB hid driver registered
2:appserver::appserver : Probe input node usbmouse
2:appserver::appserver : Found USB mouse device node
2:appserver::input_thread : Save config of /boot/system/drivers/dev/bus/usb
2:appserver::input_thread : Save config of /boot/system/drivers/dev/bus/scsi
2:appserver::input_thread : Save config of /boot/system/drivers/dev/bus/agp
2:appserver::input_thread : Save config of /boot/system/drivers/dev/bus/ata
2:appserver::input_thread : Save config of /boot/system/drivers/dev/bus/pci
2:appserver::input_thread : Save config of /boot/system/drivers/dev/bus/acpi
2:appserver::input_thread : ATi Radeon X850 XT PE (R480) closed
2:appserver::input_thread : Send TERM signals
2:mediaserver::mediaserver : Device /boot/system/drivers/dev/acpi_cpu on bus acpi is disabled
[/code:1]
Back to top
View user's profile Send private message
Kaj
The Knights of Syllable


Joined: 14 Sep 2007
Posts: 2035
Location: Friesland

PostPosted: Fri Mar 20, 2009 4:20 pm    Post subject: Reply with quote

Yes, this is a known problem. You have to stick to low resolutions that work or disable the Radeon driver.
Back to top
View user's profile Send private message Visit poster's website
adamk



Joined: 15 Dec 2007
Posts: 54

PostPosted: Fri Mar 20, 2009 4:24 pm    Post subject: Reply with quote

When I booted into Syllable via qemu the first time, I set the resolution to 1024x768. Before booting natively, I set it back to 640x480. How low of a resolution do I need to go? Smile

Adam
Back to top
View user's profile Send private message
Kaj
The Knights of Syllable


Joined: 14 Sep 2007
Posts: 2035
Location: Friesland

PostPosted: Fri Mar 20, 2009 4:27 pm    Post subject: Reply with quote

On the machines I tried, 640x480 worked in the default setting. Some colour settings may also work in higher resolutions. It's a matter of trial and error.
Back to top
View user's profile Send private message Visit poster's website
adamk



Joined: 15 Dec 2007
Posts: 54

PostPosted: Fri Mar 20, 2009 4:32 pm    Post subject: Reply with quote

If I boot up in qemu, is there some way I can reset the appserver back to the default settings, then?

Adam
Back to top
View user's profile Send private message
Kaj
The Knights of Syllable


Joined: 14 Sep 2007
Posts: 2035
Location: Friesland

PostPosted: Fri Mar 20, 2009 4:38 pm    Post subject: Reply with quote

You mean if you have a corrupted screen? The easiest way is to not switch all virtual desktops at once, so you can switch to another virtual desktop to restore the settings.

Other than that, the settings are in system/config/appserver.
Back to top
View user's profile Send private message Visit poster's website
adamk



Joined: 15 Dec 2007
Posts: 54

PostPosted: Fri Mar 20, 2009 5:20 pm    Post subject: Reply with quote

What I was really curious about is if I boot up in qemu (where the graphics work just fine), and remove sytem/config/appserver, will it get recreated during the boot with the default settings?
Back to top
View user's profile Send private message
Kaj
The Knights of Syllable


Joined: 14 Sep 2007
Posts: 2035
Location: Friesland

PostPosted: Fri Mar 20, 2009 5:41 pm    Post subject: Reply with quote

You shouldn't remove it, but you can change the screen resolution and it should be used with the different video driver when you reboot, yes.
Back to top
View user's profile Send private message Visit poster's website
adamk



Joined: 15 Dec 2007
Posts: 54

PostPosted: Sat Mar 21, 2009 5:16 am    Post subject: Reply with quote

FYI, I have this problem with the default system/config/appserver file. Guess I will have to disable the radeon driver.

Adam
Back to top
View user's profile Send private message
adamk



Joined: 15 Dec 2007
Posts: 54

PostPosted: Sat Mar 21, 2009 5:26 am    Post subject: Reply with quote

As requested in radeon.cfg, here's a copy of radeon.cfg:

[code:1]
### ATi Radeon Appserver driver v0.1-pre4 configuration file ###

# Note: Changes will be effective after rebooting the machine

### Features
# Experimental Radeon 9500 and higher support (0 - DISABLED, 1 - Enabled)
EnableR300=1
# Experimental Radeon Mobility/IGP support (0 - DISABLED, 1 - Enabled)
EnableMobility=1
# Experimental Notebook CRT mirroring support (0 - Disabled, 1 - ENABLED)
EnableMirroring=1
# Enable/disable hardware cursor support (0 - Disabled, 1 - ENABLED)
EnableHWCursor=1

### Troubleshooting
# Turn on debugging output (0 - DISABLED, 1 - Enabled)
EnableDebug=1
# Disable the usage of the card BIOS (0 - ENABLED, 1 - Disabled)
# Note: Use this only on desktop chips
DisableBIOSUsage=0

# If this doesn't solve your problems, please post on the mailing list
# syllable-developer@lists.sourceforge.net along with your kernel log
# /var/log/kernel and this configuration file!
[/code:1]

I also set DisableBIOSUsage to 1, but that didn't change anything. Should I e-mail this to the mailing list, as well?

Adam
Back to top
View user's profile Send private message
Kaj
The Knights of Syllable


Joined: 14 Sep 2007
Posts: 2035
Location: Friesland

PostPosted: Sun Mar 22, 2009 11:11 am    Post subject: Reply with quote

Thanks. I guess the only one who could do anyhting with this is Vanders right now, so he will see it here.
Back to top
View user's profile Send private message Visit poster's website
adamk



Joined: 15 Dec 2007
Posts: 54

PostPosted: Sun May 17, 2009 2:29 pm    Post subject: Reply with quote

FYI, this is still a problem in 0.6.6.

Adam
Back to top
View user's profile Send private message
adamk



Joined: 15 Dec 2007
Posts: 54

PostPosted: Wed Aug 19, 2009 4:39 pm    Post subject: Reply with quote

And the July 1st development build.
Back to top
View user's profile Send private message
Kaj
The Knights of Syllable


Joined: 14 Sep 2007
Posts: 2035
Location: Friesland

PostPosted: Wed Aug 19, 2009 7:22 pm    Post subject: Reply with quote

Yes, unfortunately, there have been no changes to the Radeon driver in a long time. It would be great if someone could update our driver port to the latest Linux version.
Back to top
View user's profile Send private message Visit poster's website
adamk



Joined: 15 Dec 2007
Posts: 54

PostPosted: Sat Oct 24, 2009 1:54 pm    Post subject: Reply with quote

Does the radeon driver work for anyone here? Perhaps it would be best to set EnableR300 to 0 by default?

Adam
Back to top
View user's profile Send private message
Display posts from previous:   
Post new topic   Reply to topic    Syllable Forum Index -> Bugs All times are GMT - 6 Hours
Goto page 1, 2  Next
Page 1 of 2

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group